GreatLight CNC Machining Factory logo
CNC Machining
Rapid Prototyping
Materials
Industries
News
About GL

Get Instant Quote

Buyer guide

What Drives CNC Machining Cost Per Hour

A quoted hourly rate is a blended number, not a machine rental fee. This guide breaks down the five cost groups behind it and shows how to read a quote line by line before you compare suppliers.

Machine classSetup amortizationTooling wearTolerance cost
Engineer reviewing a CNC machining cost per hour breakdown at a vertical mill
The short version

Key takeaways

The rate is blendedSpindle time, operator attention, overhead and depreciation sit inside one number.
Machine class sets the floorA 3-axis VMC and a simultaneous 5-axis cell cannot carry the same rate.
Setup hits small lots hardestA 10-hour setup on 25 parts adds more per part than the cut itself.
Tolerance is a multiplierEach tightening step adds cycle time and inspection cost, not just a nicer finish.
Compare quote scope, not rateTwo shops at $60/hr and $95/hr can be equally profitable on the same part.
Cost drivers

Five cost groups inside one hourly rate

Use this table to see which drivers matter most for your part before you compare quotes.

Cost driverTypical share of rateWhat moves it
Machine class and capital20–30%Spindle taper, axis count, machine price
Setup and programming10–25%Lot size, fixture complexity, first-article checks
Tooling and consumables5–15%Material hardness, tool life, insert count
Labor and burden40–60%Wage, taxes, rent, supervision, utilities
Inspection and scrap5–15%Tolerance band, CMM time, reject rate
Tolerance cost ladder

What each tolerance band adds to the hourly cost

Tolerance bandTypical methodCost effect
±0.1 mm (±0.004 in)Standard 3-axis millingBase rate
±0.025 mm (±0.001 in)Better tooling, in-process checks20–40% more cycle time
±0.005 mm (±0.0002 in)Climate room, jig grinding, CMM50–100% more cycle time
Ra 0.8–1.6 μmFinishing pass, sharp tool10–25% more cycle time
Ra 0.2–0.8 μmPolishing or fine finishingAdds a separate operation

The verdict

Compare total quoted price at a fixed lot size, with setup, tooling and inspection shown as separate lines. The hourly rate is the last thing to look at, not the first.

Why one number misleads

Why a single hourly rate hides the real cost

Two shops quote the same part at $60/hr and $95/hr. Neither is wrong. The lower rate may include setup as a flat lot charge, while the higher one spreads programming and fixturing into the hourly figure. Compare the rate alone and you learn almost nothing about the final price.

A quoted rate usually covers spindle time, operator attention, overhead and depreciation. It does not tell you how many hours the job will take. Cycle time is set by material, geometry and tolerance, and that is where most of the money is won or lost.

Shops also band their rates by machine class. A 3-axis vertical mill might sit at $45–$75/hr, a 4-axis or live-tool lathe at $75–$120/hr, and a high-end 5-axis or mill-turn cell at $100–$200/hr. Those bands are a starting point, not a verdict on quality.

Ask what the rate includes before you ask what it is. Setup, tooling, inspection and finishing are the four items most often moved in or out of the hourly number.

Capital and class

Machine class and capital recovery

Machine class dominates the base rate. A 40-taper VMC with a 10,000 rpm spindle and a 20-tool carousel carries a different cost structure than a 30-taper drill-tap center running 24,000 rpm. The second machine costs more per hour but may cut aluminum three to five times faster in light passes.

Capital recovery is simple arithmetic. A $150,000 machine amortized over 7 years at 2,000 spindle hours per year works out to about $10.70/hr before interest, maintenance and floor space. Add those and the true ownership cost roughly doubles.

This is why a shop with 16 simultaneous 5-axis centers quotes differently from a job shop with three 3-axis mills. The rate reflects the balance sheet, not just the spindle.

For your part, the question is whether the geometry needs the extra axes. A bracket with holes on five faces saves setup time on a 5-axis machine. A flat plate with two-sided pockets does not.

Setup and tooling

Setup, programming, fixturing and tooling

Setup is the most under-quoted driver on small batches. A simple 3-axis job with soft jaws and a proven program may take 0.5–1.5 hours. A 5-axis part with custom fixturing, probe calibration and first-article checks can take 6–12 hours. At $80/hr, a 10-hour setup on a 25-piece order adds $32 per part before the first chip.

Most shops quote setup as a flat lot charge. That is fairer than hiding it in the hourly rate, because the cost does not scale with quantity. Ask for it as a separate line so you can compare lot sizes honestly.

Tooling is billed inconsistently. Carbide end mills run $25–$120 each. A 1/2-inch variable-helix finisher might last 20–60 hours in 6061 but only 2–5 hours in 17-4 PH stainless. Drills, taps and inserts add up fast in production.

A job cutting Inconel 718 may consume $15–$40 of tooling per part. The same geometry in aluminum may use less than a dollar. Material choice moves tooling cost more than most buyers expect.

  • 1
    Ask for setup as a line itemFixed lot charge, not buried in the hourly rate.
  • 2
    Check tool life assumptionsStainless and nickel alloys wear tools 5–20x faster than 6061.
  • 3
    Confirm fixture ownershipCustom fixtures may be billed once or amortized across the lot.
People and overhead

Labor, burden and overhead

Labor and burden typically make up 40–60% of an hourly rate. A machinist wage might be $22–$35/hr, but the billed rate includes payroll taxes, benefits, supervision, front-office staff, rent, insurance and utilities. That is commonly a 1.8–2.5x multiplier on wage.

One operator can tend two or three VMCs with short cycle times. A 5-axis cell with long cycles may need near-continuous attention. The same wage line therefore produces very different hourly rates depending on the cell layout.

Overhead also covers programming, scheduling, quality staff and shipping. A shop with IATF 16949 and ISO 13485 certification carries more of these costs than a general job shop, and its rate reflects that.

Do not treat burden as padding. It is the part of the rate that keeps the lights on and the CMM calibrated.

Tolerance and material

How tolerances, finish and material move the rate

Tolerance is a cost multiplier that buyers underestimate. Standard machining holds ±0.1 mm (±0.004 in) comfortably. ±0.025 mm (±0.001 in) is routine but demands better tooling and more frequent checks. ±0.005 mm (±0.0002 in) usually requires a climate-controlled room, jig grinding or fine boring, and CMM verification. Each tightening step can add 20–100% to cycle time and inspection cost.

Surface finish works the same way. As-machined at Ra 1.6–3.2 μm is standard. Ra 0.8–1.6 μm needs a finishing pass and a sharper tool. Ra 0.2–0.8 μm may need polishing or a dedicated finishing operation after machining.

Material removal rate sets cycle time. Aluminum 6061 cuts at 300–600 m/min surface speed with carbide. 304 stainless drops to 120–180 m/min. Inconel 718 may run 30–50 m/min with coated carbide and heavy flood coolant. Tool steel above 45 HRC needs carbide or CBN and lighter depths of cut.

Geometry matters as much as material. Thin walls, deep pockets and long tools force light passes and slow feed rates. A part that looks simple on screen can take three times the cycle time of a compact block with the same volume.

How to compare quotes

Step by step: reading a quote line by line

  • 1
    Separate setup from run timeAsk for the setup hours and the lot charge. A fixed charge should not grow with quantity.
  • 2
    Confirm the machine class quotedCheck the axis count and spindle taper. A 5-axis rate on a 3-axis part is a red flag.
  • 3
    Check tooling treatmentIncluded in the rate, billed per part, or a one-time charge. Write it down.
  • 4
    Match tolerance to the drawingConfirm the shop quotes to your stated band, not a tighter one you did not ask for.
  • 5
    Ask what inspection is includedFirst-article CMM, in-process checks, or 100% inspection. Each has a different cost.
  • 6
    Compare at the same lot sizeA 10-piece and a 1,000-piece quote are not comparable once setup is amortized.
FAQs

Questions buyers ask about hourly rates

Why do two shops quote very different hourly rates for the same part?

The rate is a blended number, and shops blend differently. One may include setup and tooling in the hourly figure, another bills them as separate lines. Machine class, certification scope and local wage levels also differ.

Compare the total price at the same lot size with the same drawing revision. The rate alone will not tell you which quote is lower.

Is a lower hourly rate always cheaper?

No. A shop with a lower rate but a longer cycle time or a higher scrap allowance can cost more per good part. Ask for the cycle time estimate and the assumed scrap rate.

A shop quoting ±0.005 mm capability at a low rate is also worth a second look at its inspection equipment.

How does lot size change the effective rate?

Setup is fixed. At 10 parts, a 10-hour setup adds a large amount per part. At 1,000 parts, the same setup almost disappears from the per-part price.

This is why a 3-axis job can look expensive at low volume and cheap at high volume, while a 5-axis job with a long setup never fully recovers on small lots.

Should tooling be a separate line item?

Either way is fair, as long as it is stated. Separate lines make comparison easier, especially in stainless, titanium and nickel alloys where tool life is short.

If tooling is bundled into the rate, ask what tool life the shop assumed.

What does certification add to the rate?

ISO 9001, IATF 16949 and ISO 13485 each require documented processes, traceability and staff time. That cost sits in the burden portion of the rate.

For non-regulated parts, a general job shop may be cheaper. For medical or automotive parts, the documentation is part of what you are buying.

How do I know the quoted rate is realistic?

Ask for the cycle time, setup hours and inspection plan behind the number. A quote that cannot show those three is a guess.

At GreatLight, quotation and DFM analysis come back within 12 hours, with the cost lines separated so you can check them.

Send your drawing and get a cost breakdown

We quote with setup, tooling and inspection shown as separate lines, so you can compare at the same lot size.

12-hour quoteFree DFM analysis100% inspection before shipment

Follow GreatLight

More from the shop floor

We publish setup notes, tooling trials and inspection data from the factory floor.

FacebookTikTokYouTubeLinkedInInstagramThreadsPinterest

Trusted by engineers and manufacturers worldwide

Tesla Ford Motor Company BYD Auto Denso Magna International Boeing Airbus Medtronic KUKA FANUC